I.what will you notice before testing
The output of the withstanding voltage tester can output 20kV, the highest voltage. Any false operation will result in the misadventure even death. So please read this chapter carefully with the view of safety.
1.An electric shock
In order to avoiding the electric shock, please wear the rubber-insulated gloves before using the tester.
2.The tester is in the testing state
When the tester is running in the testing state, the P-wire, the tested device, the test probe and the output port all carry the high voltage. Please don‟t touch!
3.Changing the tested device
After finishing testing, when you change another tested device, please check to be sure:
①The tester is in the reset state.
②The test light is not flicking.
③ The figure of the voltage in the liquid-crystal display is not changing.
Especially notice: Don’t touch the high voltage probe when changing the tested device.
4.Switch on or off the power switch
Once the power is cut off, please wait for a minute if you want to start it once more.
Caution: It is very dangerous in the high voltage output state to change the power state, “on” or “off”, continuously. It also do harm to the tester.
Don’t join the output port of the high voltage with any things when switching on or off the power for it maybe cause the abnormal high voltage output which is very hazard.
5.Emergency treatment
In order to avoiding the more loss, please do according to the following way under any emergent conditions such as an electric shock, the burning of the tested device or the host:
①First cut off the power.
②Then unplug the plug of the power.
6.Trouble occurring
The following situations are very dangerous. Be careful please! Because it may still output the high voltage even you press the “RESET”.
①The test light is still going on when presses the “RESET” down.
②The voltmeter shows no readout while the test light is still going on.
When one of the situations occurs, please cut off the power and unplug its plug, and don‟t use it any more. The trouble is very dangerous. Please bring it to our company or the business-acted place to repair.
7.Trouble of the test light
The voltmeter shows the readout while the test light doesn‟t light after the “TEST” is pressed. This state may be the trouble of the test light. Please make the tester off and bring it to our company or the business-acted place to repair.
II.Technical parameter
1.Model List
MODEL | |
CS2670A | ACW: 5kV, 20mA |
CS2670A-1 | ACW: 5kV, 20mA |
CS2670AX | ACW: 5kV, 20mA |
CS2670Y | ACW: 5kV, 20mA |
CS2671AX | ACW: 10kV, 20mA; DCW: 10kV, 10mA |
CS2671BX | ACW: 10kV, 50mA; DCW: 10kV, 20mA |
CS2671TX | ACW: 10kV, 100mA |
CS2672BX | ACW: 5kV, 100mA |
CS2672CX | ACW: 5kV, 100mA DCW: 5kV, 20mA |
CS2672DX | ACW: 5kV, 20mA DCW: 5kV, 10mA |
CS2673X | ACW: 5kV, 200mA |
CS2674AX | ACW: 20kV, 10mA; DCW: 20kV, 10mA |
2.Technical parameters
①CS2670A/CS2670A-1/CS2670AX
MODEL | CS2670A | CS2670A-1 | CS2670AX | CS2670Y | |||
ACW | Output voltage | （0.00~5.00）kV | |||||
Max. output power | 100VA（5.000kV/20mA） | ||||||
Max. current | 20mA | ||||||
Current range | 2mA、20mA | ||||||
Output waveform | sine wave | ||||||
Waveform distortion | ≤5%（unload or pure resistance load） | ||||||
Test time | 0.0s～999s 0=continue | ||||||
Volt meter | Range | 0.00kV～5.00kV | |||||
Accuracy | ±（5%+5 word ） | ||||||
resolution | 10V | ||||||
Displayed value | RMS | ||||||
Ammeter | Range | AC | 0.100mA ～ 20.00mA | ||||
resolution | AC | 2mA：1uA， 20mA：10uA | |||||
Accuracy | ±（5%+5 words ） | ||||||
Timer | Range | 0.0s～999s | |||||
Min. resolution | 0.1s | ||||||
Accuracy | ±（1%+50ms） | ||||||
PLC interface | no | no | yes | no | |||
Remote interface | yes | ||||||
②CS2671AX/CS2671BX/CS2671TX
MODEL | CS2671AX | CS2671BX | CS2671TX | ||||
AC W | Output voltage | （0.00~10.00）kV | |||||
Max.output power | 100VA | 500VA | 1000VA | ||||
Max. current | 20mA | 50mA | 100mA | ||||
Current range | 2mA、20mA | 2mA、20mA、50mA | 2mA、20mA、100mA | ||||
Output waveform | sine wave | ||||||
Waveform distortion | ≤5% | ||||||
Test time | 0.0s～999s 0.0= continue | ||||||
D CW | Output voltage | （0.00~10.00）kV | |||||
Max. output power | 100VA | 500VA | -------------------- | ||||
Max. current | 10mA | 20mA | -------------------- | ||||
Current range | 2mA、10mA | 2mA、20mA | -------------------- | ||||
Ripple factor | ≤5% | ||||||
Test time | 0.0s～999s 0= continue | ||||||
Volt meter | Range | （0.00~10.00）kV | |||||
Accuracy | ±（5%+5 words ） | ||||||
resolution | 10V | ||||||
Displayed value | RMS | ||||||
Ammeter | Measure Range | AC | 0.100mA ～ 20.00mA | 0.100mA ～ 50.00mA | 0.100 ～ 100.0mA | ||
DC | 0.100mA ～ 10.00mA | 0.100mA ～ 20.00mA | -------------------- | ||||
Resolution | AC | 2mA：1uA，20mA：10uA,50mA（100mA）：0.1mA | |||||
Accuracy | ±（5%+5 words ） | ||||||
Timer | Range | 0.0s～999s | |||||
Min. resolution | 0.1s | ||||||
Accuracy | ±（1%+50ms） | ||||||
PLC interface | no | no | Yes | ||||
Remote interface | yes | ||||||
③CS2672BX/CS2672CX/CS2672DX
MODEL | CS2672BX | CS2672CX | CS2672DX | |||
A C W | Output voltage | （0.00~5.00）kV | ||||
Maxoutput power | 500VA | 100VA | ||||
Max. current | 100mA | 20mA | ||||
Current range | 2mA、20mA、100mA | 2mA、20mA | ||||
Output waveform | sine wave | |||||
Waveform distortion | ≤5% | |||||
Test time | 0.0s～999s 0.0= continue | |||||
D C W | Output voltage | ----------------------------- | （0.00~5.00）kV | （0.00~5.00）kV | ||
Max. output power | ----------------------------- | 100VA | 50VA | |||
Max. current | ----------------------------- | 20mA | 10mA | |||
Current range | ----------------------------- | 2mA、20mA | 2mA、10mA | |||
Ripple factor | ----------------------------- | ≤5% | ||||
Test time | ----------------------------- | 0.0s～999s 0= continue | ||||
Volt meter | Range | （0.00~50.00）kV | ||||
Accuracy | ±（5%+5 words ） | |||||
resolution | 10V | |||||
Displayed value | RMS | |||||
Ammeter | Measure Range | AC | 0.100mA ～ 100.0mA | 0.100mA ～ 100.0mA | 0.100mA～20.00mA | |
DC | ---------------------------- | 0.100mA ～ 20.00mA | 0.100mA～10.00mA | |||
Resolution | 2mA：1uA， 20mA：10uA, 50mA：0.1mA | |||||
Accuracy | ±（5%+5 words ） | |||||
Timer | Range | 0.0s～999s | ||||
Min. resolution | 0.1s | |||||
Accuracy | ±（1%+50ms） | |||||
PLC interface | no | no | Yes | |||
Remote interface | yes | |||||
④CS2673X/CS2674AX
MODEL | CS2673X | CS2674AX | ||||
A C W | Output voltage | （0.00~5.00）kV | （0.00~20.00）kV | |||
Max. output power | 500VA | 200VA | ||||
Max. current | 200mA | 20mA | ||||
Current range | 2mA、20mA、200mA | 2mA、10mA | ||||
Output waveform | sine wave | |||||
Waveform distortion | ≤5% | |||||
Test time | 0.0s～999s 0.0= continue | |||||
D C W | Output voltage | -------------------------------- | （0.00~20.00）kV | |||
Max. output power | -------------------------------- | 200VA | ||||
Max. current | -------------------------------- | 10mA | ||||
Current range | -------------------------------- | 2mA、10mA | ||||
Ripple factor | ≤5% | |||||
Test time | 0.0s～999s 0= continue | |||||
Volt meter | Range | （0.00~5.00）kV | （0.00~20.00）kV | |||
Accuracy | ±（5%+5 words ） | |||||
resolution | 10V | |||||
Displayed value | RMS | |||||
Ammeter | Measure Range | AC | 0.100mA ～ 200.00mA | 0.100mA ～ 10.00mA | ||
DC | ----------------------------------- | 0.100mA ～ 10.00mA | ||||
Resolution | 2mA：1uA， 20mA：10uA, 200mA：0.1mA | |||||
Accuracy | ±（5%+5 words ） | |||||
Timer | Range | 0.0s～999s | ||||
Min. resolution | 0.1s | |||||
Accuracy | ±（1%+50ms） | |||||
PLC interface | no | no | Yes | |||
Remote interface | yes | |||||
中文
English
+86-312-6775656
+86 13731210226
sales03@bdhuazheng.com
